Portronics Zeno B — Complete Guide

TABLE OF CONTENTS

• Product Overview
• Quick Reference
• What's in the Box
• Parts & Controls
• Massage Heads & Their Uses
• Attaching or Changing a Massage Head
• Charging the Zeno B
• Understanding the Battery Indicators
• Switching the Massager ON and OFF
• Selecting the Speed
• Using the Extension Rod
• How to Use
• Pressure Protection
• Working Time
• Safety & Care
• Still stuck?

Product Overview

The Portronics Zeno B is a rechargeable percussion gun massager with a brushless DC motor, an extended reach handle and six interchangeable massage heads. It offers five speed levels up to 3200 RPM for different muscle areas and massage preferences.

Quick Reference

Actual runtime depends on the selected speed, pressure applied and battery condition.

What's in the Box

Parts & Controls

Massage Heads & Their Uses

Choose the massage head according to the target muscle area and the type of massage you prefer.

Use only a suitable attachment and apply comfortable pressure. Do not use the massager without a massage head fitted securely.

Attaching or Changing a Massage Head

1. Switch the massager OFF before changing the massage head.
2. Select the head suitable for the intended area.
3. Align the connecting end of the head with the massager stem.
4. Press the massage head firmly into place.
5. Check that it is seated securely before switching the device ON.
6. To remove it, pull the head out gently.

Do not force an attachment into the connector.

Charging the Zeno B

1. Switch the massager OFF before charging.
2. Connect the supplied Type-C charging cable to the charging port.
3. Connect the other end to a compatible USB adapter.
4. Check the LED indicators to monitor charging.
5. Allow approximately 2–3 hours for charging.
6. The LEDs stop flashing once the battery is fully charged.
7. Disconnect the charging cable before using the massager.

Important: The massager cannot be turned ON while it is charging. Use only the supplied Type-C charging cable.

Understanding the Battery Indicators

• Green LEDs show the battery charge status, from approximately 20% to 100%.
• The LEDs flash while charging.
• The LEDs stop flashing once the battery is fully charged.

Battery life varies depending on the selected speed and intensity of use.

Switching the Massager ON and OFF

1. Press and hold the Power Button for approximately 2–3 seconds to switch the massager ON.
2. The massager starts operating.
3. To switch it OFF, press and hold the Power Button again for approximately 2–3 seconds.

Selecting the Speed

1. Switch the massager ON.
2. Short-press the Power Button to cycle through the available speed levels.
3. Select one of the five speed levels, up to 3200 RPM.
4. Start at a lower speed and increase gradually as comfortable.

The device may automatically stop if excessive pressure is applied during massage. Reduce pressure before restarting.

Using the Extension Rod

The extension rod helps reach areas that are difficult to access directly.

1. Switch the massager OFF before attaching or adjusting the extension rod.
2. Align the rod with the designated attachment point.
3. Secure it properly before use.
4. Hold the device steadily and apply light to moderate pressure.
5. Do not force the rod or press excessively against the body.

How to Use

1. Choose the massage head appropriate for the target area.
2. Switch the device OFF and press the selected head firmly into place.
3. Switch the massager ON by holding the Power Button for approximately 2–3 seconds.
4. Short-press the Power Button to select the desired speed.
5. Place the massage head against the intended muscle area.
6. Move the massager gently across the area using comfortable pressure.
7. Avoid keeping the massager on the same area for more than 60 seconds continuously.
8. After 1 hour of use, switch it OFF and let the device rest for 30 minutes before using it again.
9. After use, clean or wipe the massage heads before storage.

Pressure Protection

The massager includes a pressure-protection function. If excessive pressure is applied during massage, the device automatically stops.

If this happens:

1. Release pressure from the massage area.
2. Check that the massage head is securely fitted.
3. Restart the massager and use lighter pressure.

Do not force the device against the body to keep it running.

Working Time

The approximate working time is 3–4 hours on a full charge. Actual usage time varies according to speed level, pressure and operating conditions.

Safety & Care

• Do not use the device while charging. Ensure it is switched OFF before charging.
• Use only the supplied Type-C charging cable.
• Do not massage the same area for more than 60 seconds continuously.
• After 1 hour of use, switch OFF and allow the device to rest for 30 minutes.
• Do not apply excessive pressure; the device may stop automatically if too much pressure is detected.
• Do not drop, crush or apply strong impact to the massager.
• Keep it away from water, liquids and high moisture.
• Do not use the device if it is damaged or malfunctioning.
• Do not disassemble or attempt to repair the device yourself.
• Keep it away from flammable or explosive substances.
• Clean or wipe the massage heads after use.
• Clean the device with a dry cloth. For stubborn stains, use mild detergent and wipe dry.
• If storing for a long period, charge it once and keep it in its original packaging in a dry place.

Still stuck?

If the issue persists after performing all troubleshooting steps, please raise a support request.

Our support team will assist you further.

Support

• Visit: www.portronics.com
• Support Portal: support.portronics.com