Portronics Harmonics Y3 — Complete Guide

TABLE OF CONTENTS

• Product Overview
• Quick Reference
• What's in the Box
• Parts & Controls
• Powering On and Off
• First-Time Bluetooth Pairing
• Reconnecting to Bluetooth
• Dual-Device Pairing
• Music Controls
• Hands-Free Calling
• Voice Assistant
• Music Mode and Game Mode
• Charging
  • LED Indicator Guide
• Clearing Pairing / Reconnecting
• Care & Safety
• Still stuck?

Product Overview

The Portronics Harmonics Y3 is a wireless neckband headset with magnetic earbuds, in-line controls, dual-device pairing and Music/Game modes. It supports hands-free calling, voice-assistant access and USB Type-C charging.

Quick Reference

What's in the Box

Parts & Controls

Powering On and Off

• Power ON: Separate the magnetic earbuds. The headset turns on and announces that it is ready to pair.
• Power OFF: Press and hold the MFB for about 4 seconds.
• If no Bluetooth connection is made within approximately 5 minutes, the headset automatically powers off.
• When the earbuds are attached magnetically, handle and store them together to keep them tidy.

First-Time Bluetooth Pairing

1. Turn on the headset by separating the magnetic earbuds.
2. If it is not already in pairing mode, press and hold the MFB for about 2 seconds.
3. Wait for the red and blue LEDs to flash alternately and for the pairing voice prompt.
4. Enable Bluetooth on your phone.
5. Search for Harmonics Y3.
6. Select the headset to pair.
7. When connected, the headset announces “Connected”. The blue LED flashes once every 5 seconds.

Reconnecting to Bluetooth

When powered on, the headset can reconnect automatically to the last paired phone.

If it does not reconnect:

1. Turn Bluetooth on on the phone.
2. Select Harmonics Y3 from the saved-device list.
3. Keep the phone within approximately 10 metres for a stable connection.
4. If needed, disconnect the headset and enter pairing mode again.

Dual-Device Pairing

Harmonics Y3 supports connecting to two devices.

1. Pair the headset with Device 1.
2. Turn Bluetooth off on Device 1.
3. Pair the headset with Device 2.
4. Turn Bluetooth back on on Device 1.
5. Both devices should remain paired with the headset.

If dual pairing does not work, disconnect unused Bluetooth devices and repeat the steps in the same order.

Music Controls

Hands-Free Calling

For clearer calls, keep the phone within range and ensure the microphone is not covered.

Voice Assistant

Press and hold the MFB for about 2 seconds to activate the supported voice assistant, if enabled on your phone.

Music Mode and Game Mode

Triple-click the MFB to switch between Music Mode and Game Mode.

Use Music Mode for everyday listening and Game Mode when you want the headset's gaming audio mode.

Charging

1. Connect a USB Type-C cable to the headset's charging port.
2. Connect it to a suitable 5V/1A USB power source.
3. Check the LED indicator for charging status.
4. Disconnect the headset after charging is complete.

LED Indicator Guide

Clearing Pairing / Reconnecting

If the headset does not connect properly:

1. Disconnect it from the phone or remove the saved Harmonics Y3 entry from Bluetooth settings.
2. Press and hold the MFB for about 2 seconds to enter pairing mode.
3. Wait for alternating red and blue LEDs.
4. Select Harmonics Y3 on the phone to pair again.

Care & Safety

• Avoid extreme heat, cold and humidity.
• Do not drop or crush the headset.
• Avoid pulling, sharply bending or putting excessive force on the neckband cable.
• Keep the phone within approximately 10 metres for reliable connectivity.
• Use a suitable quality-certified charger with the Type-C port.
• Do not use damaged charging accessories.
• If you experience discomfort or pain, lower the volume or stop listening temporarily.
• Avoid prolonged listening at maximum volume.

Still stuck?

If the issue persists after performing all troubleshooting steps, please raise a support request.

Our support team will assist you further.

Support

• Visit: www.portronics.com
• Support Portal: support.portronics.com